Colour perception, especially with models, is an often debated topic especially when manufacturers occasionally, and some more than others, appear to get it wrong. There can be several reasons why colours on models do not always appear correct. In this post I look at some of the issues and reasons that can influence getting colours correct. I have been constructively critical in the past of some manufacturers attempts at getting colours / liveries correct and often try to get colours and liveries corrected, if possible, and have done so again only recently with some proposed SR locomotives (naming no names but fingers crossed they arrive OK).
I will use LSWR/SR Goods Wagon Brown as a case in point; for example, Hornby have had multiple attempts to achieve the correct SR colour. Back in 2016 their excellent SR Diagram 1530, as per my review here, was released in a good, if not very slightly too dark, representation of the SR Goods Wagon Brown.
By 2020 the colour on their ex LSWR Warner 20T SR diagram 1543 brake vans, as I highlighted here, was the wrong shade of chocolate.
Perhaps the fact that the official name of the correct dark brown colour is “Chocolate Brown” they chose milk chocolate instead?
Hornby have subsequent released further versions of this model in a darker version but is still slightly too light and lighter than the colour they used on the cattle truck!
In my day job I therefore, for my own satisfaction / reputation, had to ensure that the LSWR/SR Goods Wagon Brown on the Kernow Model Rail Centre ex LSWR Diagram 1541 Road Van that I was responsible for producing was as close to the correct colour as possible. I undertook a lot of research to be able to provide the factory with the correct paint references, although this is not as simple as it sounds as I will discuss below.
Following much historical research and checking many contemporary references I was able to provide the factory with a suitable British Standard paint colour reference, however even this is complicated by the fact that such a historical British Standard reference is now obsolete so not readily available for the factory to obtain! Careful checking and agreeing decorated samples ensured that I was happy with the factory’s interpretation of the colour to allow production to commence.
I am also only too happy to share my researched colour references with some other manufacturers, to try to achieve some consistency of colours for all Southern Railway modellers alike.
This included for example my good friends at Rapido Trains UK, and they specified with their factory my SR Goods Wagon Brown colour reference for their splendid ex SECR /SR open wagons.
I did however note in my review here, that their factory interpretation of the colour appeared lighter. I also thought at the time of writing that the finish of the model may have also affected the perception of the colour as it was a satin nearly glossy finish rather than matt.
To demonstrate this, I have now given one of the Rapido Trains UK wagons a simple single spray coat of Testers Dullcoat matt varnish and when pictured alongside the KMRC Road Van and one of the original Rapido Trains UK factory finished wagons the effect of the type finish and its perception of the same base colour can be clearly seen.
I will now apply the same treatment too all my Rapido Trains UK wagons from this batch (and I have also shared the results of this simple change of finish with Rapido Trains UK ).
It should be noted that I have purposely taken the comparison picture under the same lighting conditions. Different forms and types of lighting either when viewing the prototype, for example bright sunshine or a cloudy day, or models for example under warm or cool white lighting (see my post here about white is white…) can totally change the visual perception of a colour. I am also of course aware that you will be viewing this post on different devices and screens that will also create different perceptions of the colour!
In addition to historical superseded / obsolete colour references and paint finishes there are several other factors that need to be considered when specifying and choosing the correct colour.
Firstly, care should be taken when using old colour photographs, or for that matter preserved rolling stock, as there are so many variables that can affect the representation / comparison of any colour. As well as the lighting conditions at the time the image taken the use of different film stocks at the time and variations in any subsequent printing can give different colour hues. Something published as fact, even repeatedly or copied is not necessarily always factually correct and can still include errors or subjectivity.
Another factor to take into account especially with models is that of colour scaling; our perception of colour does not scale and will vary depending on the distance at which it is being viewed and also the size and the area of the colour, for example if you painted a model with exactly the same paint as a full-size example the model will appear darker when look at in isolation. This is therefore also an issue when using a small swatch of colour as an original reference, and this has been the case, in my opinion, with a small number of colours as referenced in otherwise excellent and well respected livery reference books.
Sometimes a model manufacturer will sometimes need to counter this by using a colour slightly lighter on the model than the full-size prototype so it ‘looks right’ to the eye.
It should also be noted that adjacent different colours to our chosen colour will affect the perception the hue, see the example shown left.
This is often highlighted when initially painting a model for example compare a lined and unlined model that uses the same base colour.
For example, a splendid malachite green Bulleid pacific will look to be a darker green until the three horizontal lines are added as can be seen in the image to the left of my 21c11 before and after lining has been applied and photographed under the same lighting conditions.
Finally, one further complication for model manufactures is the process used to recreate the often-complex liveries on a model. This is often achieved by a mixture of both paint and print applications, whereas the prototype is more often than not painted (although some modern liveries are via printed vinyls) . Different specifications are used for paint and print colours. For example, paint colours are usually specified to British Standard (both current and obsolete) or RAL numbers; whilst printing inks are usually referenced Pantone colours. There are often no direct conversions between some paint and print colours and errors can creep into the process when conversions take place. For example, sometimes a paint reference could give multiple close Pantone references, and it can even be the case that when some are converted back, they end up as a different RAL number!
It is therefore imperative that such conversions between paint and print references during the process are checked and agreed at every stage. It is the reason that creating an approved set of livery artworks must then be checked and further approved at the decorated sample stage (actual physical sample not photographs from the factory!) before production. Skipping some of these steps in the process, usually for apparent cost reasons, can easily result in mistakes, such as has occurred with the production of some models in the past and therefore be a false economy.
I hope this little walk through the hues and lows of the processes involved in getting the colour / more importantly, the perception of colours as correct as possible has been of interest, perhaps the first of an occasional “Insider insights” series? As always, I welcome and enjoy reading and responding to comments.