Posts Tagged ‘On the workbench’

As I hinted in my Workbench Witterings #10 Forward dating @Hornby Bulleid Merchant Navy 21c7 to 1947 condition post here, I also intended to do the same with my  R3435 21C3 ‘Royal Mail’ model. 

21c3 Royal Mail in May 1947 condition with freshly fitted standard smoke deflectors

21c3 in bits following an attack of a razor saw

21c3 Royal Mail

21c3 and 21c7 together what I call the posh chocolate shot

Like the latest Hornby model of 21c7 the previously released model R3435 21C3 ‘Royal Mail’ model has been produced in her early condition, with the ‘widows peak’ and without smoke deflectors. 21c3 was introduced in September 1941 in malachite green livery but repainted in plain black as a wartime measure in May 1943. Changes to the smoke deflection stated in September 1944 when she was fitted with the top cowl and short flared deflectors. 21c3 was repainted malachite green in November 1945 and was subsequently fitted with standard length and style of smoke detectors in May 1947. She stayed in this condition until June 1948 when she was renumbered 35003 and British Railways in SR style sunshine lettering.

I have therefore took the razor to hand and modelled 21c3 in her May 1947 condition just after she received freshly painted new standard deflectors, complete with the baton along the top for mounting the Devon Belle wing plates as a per a photograph of her that I have in my collection.
Like my 21c7 conversion I have used etched smoke deflectors, electric lamps and a replacement smoke box dart from the excellent Albert Goodall range supplied by my friends at RT Models. The replacement lamp irons are simply staples cut to length and I have replaced the flat printed nameplates and smokebox door roundel with etched versions from Fox Transfers.

I have followed the same steps as per my Workbench Witterings #10 post here so will not repeat the stage by stage details. Who knows when we might see this version from Hornby, as I said in the #10 post once you get over the brave step of putting a razor saw to a brand new model the modification is reasonably quick and easy to complete.

 

 

Read Full Post »

As per my review, here, of the Hornby Bulleid Merchant Navy R3717 21c7 Aberdeen Commonwealth in SR wartime black, the model has been produced in her early condition, with the ‘widows peak’ without smoke deflectors. 21c7 was one of the first batch of ten Merchant Navy pacifics, she was introduced in June 1942 in malachite green livery but was quickly repainted in plain black as a wartime measure. 21c7 remained in this condition until August 1944 when she gained the more familiar cowl above the smokebox and also received short flared smoke deflectors. She gained the to become standard length and style of smoke detectors whilst still in black in June 1947.

The forward dating complete, 21c7 in 1947 condition.

The model and new components ready to start the conversion.

The top brackets are soldered to the etched deflectors

The first cuts are the bravest… and the front fairing edges bevelled.

The new cowl is trial fitted in place.

The deflectors are curved to the correct shape prior to painting.

The new front face is complete

The finished 21c7, now awaits some weathering.

Another view of the finished 21c7

As my usual modelling period is between 1946 and 1949 I have forward dated 21c7 to the condition she was just before being outshopped in malachite green at the end of June 1947. This requires the fitting of the cowl above the smokebox, in place of the ‘widows peak’, the fitting of standard smoke deflectors, with electric lamps attached. The middle position lamp irons were also moved to the smokebox door once smoke deflectors were fitted.

For this relatively simple forward dating process I have used the following items: etched smoke deflectors, electric lamps and a replacement smoke box dart from the excellent Albert Goodall range supplied by my friends at RT Models. The replacement lamp irons are simply staples cut to length and I have replaced the flat printed nameplates and smokebox door roundel with etched versions from Fox Transfers.
The Hornby nameplates come off quite easily, they are held in place by three small lugs, one in the centre and one towards each end of the arms. I slide a sharp knife underneath from one side to the other to lift the plates. I then ensure any remaining lug was carefully cut flush to the side. I affix the etched plates using a very small amount of superglue applied with a cocktail stick (some people prefer to use a small amount of varnish instead of glue).

The first step was to fold up and solder the brackets just below the top inside edge of the etched brass deflectors. The deflectors were then bent to both their correct vertical shape and also the curve at the bottom edge to match the existing fairing. I then used the deflectors to mark the position of the horizontal cut required in the existing front fairing. An Albert Goodall electric lamp was glued on the inside front edge of each deflector lining up with bottom of the two rivets on the outside of the deflector. I then used Halfords spray cans to first prime using etched primer before top coats of satin black.

Next I took a deep breath and using a razor saw, cut horizontally,  along the previously marked lines, the fairing back to the smoke box face and then vertically downwards level with the smokebox front, this removes both the ‘widows peak and the sides to meet the horizontal cuts. I also removed the Hornby printed roundel and the smokebox door dart. The sides of the slot in front of the chimney was also filed to match the rest of the opening. With all cuts cleaned up with a fine file, I also bevelled the remaining front fairings to give them a thinner edge appearance.

The Albert Goodall cast white metal cowl was filed to suit the slot in front of the chimney and glued into place using superglue. I drilled holes in the smokebox door for the two lamp irons and the replacement door dart. The finish painted deflectors were glued into place with the top brackets affixed to the top edge of the flat top gutter strip.

The Hornby model as supplied has an all over slightly matt finish, in reality the flat top, cab room and middle section of the tender cab roof were matt, whilst the sides were more of a satin finish and the front cowl also tended to be satin. I repainted the top and the smokebox front and door matt black. Before applying the etched nameplates and roundel I masked the matt areas and sprayed the sides of the model with Halfords satin lacquer. Once the nameplates and roundel were fitted the final tasks were to fit the new Albert Goodall smokebox door dart and the Hornby supplied cylinder drain cocks.

Once you get over the brave step of putting a razor saw to a brand new model the modification is reasonably quick and easy to complete. I will at some stage do the same to my malachite green R3435 21C3 ‘Royal Mail’ model!

Read Full Post »

%d bloggers like this: